hit counter script Back to Revision
KNOCK DOWN FITTINGS COMMONLY USED IN SCHOOLS
 

Cam Bolt assembly Nylon snap together joiners Screw on Blocks Plastic Corner Blocks Drawer Runner  Barrel Nut - plastic - Plug-in shelf support  Cross Dowels

 

Image for SSU:866-497
 

 

 

Click for Larger Image

 Dowel Pin and

TWO-PIECE KNOCKDOWN FITTINGS NEARLY INVISIBLE AFTER INSTALLATION (CAM BOLT ASSEMBLY)


With a serrated, edged cam and bolt assembly to keep them tight, Two-Piece Knockdown Fittings will do a great job on furniture or projects requiring assembly and disassembly:
  • 866-497 - Cams fit into 15mm dia. x 12.5mm deep holes and tighten with slotted or Phillips screwdriver or metric hex wrench.
    Bolt assemblies come in three sizes:
    866-504 - 34mm long, 5mm "A" dia., 7mm "B" dia.
  • 866-511 - 24mm long, 5mm "A" dia., 6mm "B" dia.
  • 866-518 - 24mm long, 8mm "A" dia., 8mm "B" dia.
  • Cams and bolt assemblies sold in packages of 10.
  • http://www.woodworker.com/cgi-bin/FULLPRES.exe?PARTNUM=866-497
  •  
  • Image for SSU:927-979
     

    NYLON SNAP TOGETHER JOINERS CONNECT AND DISCONNECT, AS NEEDED
     


    White nylon snap together joiners provide a rigid, mechanical joint suitable for shelving, cabinets and other uses:

     
  • Both male and female joiners require a 3/8" dia. x 3/8" deep hole.
  • Additional fasteners required in applications designed to be "permanent".
  • http://www.woodworker.com/cgi-bin/FULLPRES.exe?PARTNUM=927-979
  •  
  •   Screw on Blocks
    Assembly Fitting - screw-on - White

    A two piece item that is screwed on.

    BB201 Dim 2.jpgBB201 in situ.jpg

     

    Plastic Corner Blocks

    The corner block is held against the two pieces of material which are to be joined at right angles. It is a relatively strong joint and has the advantage of being dismantled using a screwdriver.

    An alternative would be to use a small block of pine with pre drilled holes  which can be glued and screwed to the two pieces of wood to be joined.

    http://www.screwfix.comlternative would be to use a small block of pine with pre drilled holes  which can be glued and screwed to the two pieces of wood to

     

     

     

    Drawer Runner Single Ext. 310mm

     

    Drawer Runner Single Ext. 310mm

    http://www.woodfit.com

    Additional Information:  Made from galvanized steel the runners are guided by two ball cages (linear ball bearings) they have a carrying capacity of 10kg, and are suitable for a 17mm wide x 6mm deep grooved drawer side, and are sold in pairs.

    BR220 225 230 235Groove Runner Single extension Dim.jpg

     

    Barrel Nut - plastic - Beige

     

    Barrel Nut - plastic -

    BeigeAdditional Information:  Made from high density Beige plastic, the nut has a pilot hole into which a screw - use Hi-Lo screw 8g - is inserted which cuts it's own thread.

    BA411 412 413 419 Dim.jpg

     
     

    White Shelfsup

            

     

    Plug-in shelf support

     

    Holes are drilled in line across opposite sides of the cabinet into which the shelf support are inserted. The shelf sits on top of the supports.   http://www.screwfix.com

     
    Cross Dowels

     

     

     

     

     

     

     

     

     

     

    Cross Dowels  http://www.peckers-woodworking.com/Inserts-Connectors.php

    Use to make strong right angle joints. Dowel is steel, 16mm L x 10 mm. Shown with connector 1/4'' - 20 thread with 4 mm hex drive bolt (Item #62505 or #62471 SOLD Separately) installed. Choose the length of bolt you need

    8 per pack

    More information: http://www.rockler.com